Vibra-TITE 121 Medium Strength Removable Anaerobic Threadlocker, 10ml Bottle, Blue

Vibra-TITE 121 Medium Strength Removable Anaerobic Threadlocker, 10ml

Vibra-TITE 121 Medium Strength Threadlocker is a general purpose product. 121 will hold all metric, imperial or conventional sized nuts and bolts, meeting the requirements of over 80 percent of fastening applications. It does not run off or drip and does not migrate after assembly due to its thixotropic chemistry. Once applied, parts install easily, lubricated by the adhesive. Vibra-TITE 121 replaces lock washers, plastic inserts and locks machine access bolts, and hydraulic system bolts. Used on gear box bolts, drive shaft fasteners, bearing cover cap screws, counter sunk screws, conveyor roller bolts and construction equipment. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed without Primer is 20 minutes at 77/F. Shelf Life is 12 months at 68 degree F. 24 hours at 68 degree F Full Cure Time. 100-200 inches/lbs Typical Breakaway Strength. 30-60 inches/lbs Typical Prevailing Strength. Product should be stored in a cool and dry location at temperatures between -10 degree C to 30 degree C. Optimal storage is 22 +/- 4 degree C. Shelf life is 18 months from date of manufacture when stored at 22 +/- 4 degree C. Seals nuts and bolts ranging from 1/4'' to 3/4'' (6-20mm) in diameter wh...

  • Color: Blue
  • Brand: Vibra-TITE
  • ASIN: B0025PSNKM
  • UPC: 745619121103

Vibra-TITE 135 Permanent Strength Gel Anaerobic Threadlocker, 35 ml Pump, Red

Vibra-TITE 135 Permanent Strength Gel Anaerobic Threadlocker, 35

Suitable for applications where disassembly is not required. Permanently locks nuts or bolts up to 1/4" in diameter. Heat and hand tools required for disassembly. 0.015 inches Maximum gap fill. 200/100 lbs Torque strength, Break/Prevail. 1.1 Specific gravity. N or T Suggested primer. 35 ml Pump.

  • Color: Red
  • Brand: Vibra-TITE
  • ASIN: B002QMYQRI
  • UPC: 745619135353

Vibra-TITE 125 Removable Medium Strength Gel Anaerobic Threadlocker, 35 ml Pump, Blue

Vibra-TITE 125 Removable Medium Strength Gel Anaerobic Threadlocker,

Vibra-TITE 125 Gel Threadlocker is an anaerobic thread locking adhesive for all types of metal, threaded fasteners. Cured performance shows controlled medium strength with good temperature and solvent resistance against water and non-polar solvents. This product cures rapidly on plated, oily metal surfaces or inactive surfaces. Replaces lock washers and plastic inserts. Locks machine tool access bolts, studs, and hydraulic system bolts. Used on gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts and construction equipment. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed with Primer is

  • Color: Blue
  • Brand: Vibra-TITE
  • ASIN: B004UMONPC
  • UPC: 745619125354

Vibra-TITE 140 Permanent High Strength Anaerobic Threadlocker, 1 liter Jug, Red

Vibra-TITE 140 Permanent High Strength Anaerobic Threadlocker, 1

Vibra-TITE 140 High Strength Threadlocker is a red general purpose adhesive for permanent threaded assemblies. 140 locks fasteners up to 1" in diameter sealing against leakage and corrosion. It resists attack from most fuels, lubricants and most industrial gases. Eliminates double nutting and or welding of critical assemblies. The product’s viscosity can be used on fine to medium threaded parts that will not require periodic disassembly. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed with Primer is

  • Color: Red
  • Brand: Vibra-TITE
  • ASIN: B004UMOTW4
  • UPC: 745619140005

Vibra-TITE 111 Low Strength Removable Anaerobic Threadlocker, 10ml Bottle, Purple

Vibra-TITE 111 Low Strength Removable Anaerobic Threadlocker, 10ml

Vibra-TITE 111 Low Strength Threadlocker is a thixotropic anaerobic threadlocker designed for easy disassembly of threaded components. The anaerobic nature cures only when confined between two metal parts. The products low removal torque allows easy disassembly yet provides vibration and shock resistance. Best for small fasteners under 1/4" where prevention of vibrational loosening is required. Ideal on small set screws, brass and most types of small threaded nuts, bolts, screws, hex and slot driven components including keyed fasteners. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed without Primer is 20 minutes at 77/F. Shelf Life is 2 months at 68 degree F. 24 hours at 68 degree F Full Cure Time. 50-100 inches/lbs Typical Breakaway Strength. 20-50 inches/lbs Typical Prevailing Strength. Product should be stored in a cool and dry location at temperatures between -10 degree C to 30 degree C. Optimal storage is 22 +/- 4 degree C. Shelf life is 18 months from date of manufacture when stored at 22 +/- 4 degree C. 0.007 inches Maximum gap fill. 75/25 lbs Torque strength, Break/Prevail. 1.05 Specific gravity. N or T Suggested primer. 10 ml Bottle.

  • Color: Purple
  • Brand: Vibra-TITE
  • ASIN: B0026GJ9TE
  • UPC: 745619111104

Vibra-TITE 146 Permanent Large Diameter High Strength Anaerobic Threadlocker, 1 liter Jug, Red

Vibra-TITE 146 Permanent Large Diameter High Strength Anaerobic

Vibra-TITE 146 Large Diameter High Strength Threadlocker is a red general purpose adhesive for permanent threaded assemblies. 146 locks fasteners 1" and larger in diameter, sealing against leakage and corrosion. It resists attack from lubricants and most industrial liquids and gases. Eliminates double nutting and/or welding of critical assemblies. Using Vibra-TITE 146 permits reduced casting thickness, and eliminates cracked castings due to interference fit stresses. It is recommended for larger diameter studs with coarse threads and is used to reclaim worn stud holes. Primers are recommended for large gaps and poor fitting parts. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed with Primer is

  • Color: Red
  • Brand: Vibra-TITE
  • ASIN: B004UMOUW8
  • UPC: 745619146007

Heitaisi 50ML 271 Thread Locker Glue Screw Glue Anaerobic Glue Red Glue Medium Strength Threadlocker 271 Anaerobic Adhesive for LOCTZTE

Heitaisi 50ML 271 Thread Locker Glue Screw Glue

Description: Weight: 50ml / supportColor: blue Density: 1Temperature resistance: -54 ° C -150 ° CViscosity: 400/600 (mpa.s)Shelf life: 18 monthsCuring speed: 24 hours solidTypical use: medium strength, detachableShear strength: 18/26MPaMain adhesive material: mostly used for metal surfacesInstructions: - For best performance, the surface must be clean and free of grease- This product is most suitable for occasions with small bonding gap (0.05mm)- Excess adhesive can be dissolved with detergent, nitromethane or acetone

  • Color: r
  • Brand: Heitaisi
  • ASIN: B07RKN6TQB
  • UPC: 015941481634

Vibra-TITE 12506BC 125 Removable Medium Strength Gel Anaerobic Threadlocker, 125, Blue (Тhrее Pаck)

Vibra-TITE 12506BC 125 Removable Medium Strength Gel Anaerobic

Vibra-Tite 125 gel Threadlocker is an anaerobic thread locking adhesive for all types of metal, threaded fasteners. Cured performance shows controlled medium strength with good temperature and solvent resistance against water and non-polar solvents. This product cures rapidly on plated, oily metal surfaces or inactive surfaces. Replaces lock washers and plastic inserts. Locks machine tool access bolts, studs, and hydraulic system bolts. Used on gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts and construction equipment. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the tube onto threaded parts. Seals nuts and bolts ranging from 1/4'' to 3/4'' (6-20mm) in diameter while allowing disassembly using standard tools. 0.015 inches maximum gap fill. 1.1 specific gravity. Primer N or T suggested. Fixture speed with primer is less than 70 seconds. Fixture speed without primer is 10-30 min at 77 degree F. Full cure time is 24 hours at 68 degree F . 3/8 phos-oil 120 lbs/inches typical Breakaway strength. 3/8 phos-oil 45 lbs/inches typical prevailing strength. Shelf life is 24 months from date of manufacture when stored at 25 +/- 2.7 degree C (77 +/- 5 Degrees Fahrenheit).

  • Brand: Vibra-TITE
  • ASIN: B07PSCCF1J
  • UPC: 756990904995

Vibra-TITE 131 Permanent Strength Anaerobic Threadlocker, 1 liter Jug, Red

Vibra-TITE 131 Permanent Strength Anaerobic Threadlocker, 1 liter

Vibra-TITE 131 Permanent Strength Threadlocker is a product designed to provide medium-high strength threadlocking where controlled torque / tension is required. Material lubricates during assembly, securing parts with medium-high strength retention allowing disassembly when required. Best for applications where parts require locking strength but may need to be disassembled. Vibra-TITE 131 resists vibrational loosening however if used on large diameter bolts or where there is a long engagement of the fastener, the application of heat may be required for removal. Ensure parts are clean, dry and free from oil and grease before use. Product is normally hand applied from the bottle onto threaded parts. Fixture Speed with Primer is

  • Color: Red
  • Brand: Vibra-TITE
  • ASIN: B004UMOQ4U
  • UPC: 745619131003

Jannyshop 2 PCS Thread Locker Glue Screw Glue Anaerobic Glue Red Glue for LOCTZTE 271(50ml)

Jannyshop 2 PCS Thread Locker Glue Screw Glue

Features: 1.Retention positioning: fill the matching gap, firm and durable, stable and reliable, reduce maintenance costs2.Sealed and leakproof: instead of solid gasket, close contact, durable seal, effective leak proof3.Tight lock anti-loose: Say goodbye to the traditional mechanical locking method, solidify to form a strong plastic film, the lock is not loose.4.Temperature and pressure resistance: The working temperature range is upgraded to 360F to prevent movement, looseness and corrosion.5.Universal and wide: widely used to bond various metal screws to protect the machine for a long time.6. Good oil solubility: the oil has the ability to repair the tolerance, no need to cleanDescription: Weight: 50ml / supportColor: blue Density: 1Temperature resistance: -54 ° C -150 ° CViscosity: 400/600 (mpa.s)Shelf life: 18 monthsCuring speed: 24 hours solidTypical use: medium strength, detachableShear strength: 18/26MPaMain adhesive material: mostly used for metal surfacesList: 2*243 anaerobic adhesive

  • Color: Color
  • Brand: Jannyshop
  • ASIN: B07RDDCXDV
  • UPC: 015941990631
Similar Anaerobic Threadlocker Results
Anaerobic Threadlocker Video Results
           

In the Lab with LOCTITE® - Proper Use of Threadlocker

Anaerobic Threadlocker

Host Phil Godeck and Henkel Engineer, Andrew Paluch, demonstrate how to properly apply LOCTITE® anaerobic threadlockers to achieve maximum benefits. LOCTITE® Anaerobic Threadlockers: http://na.henkel-adhesives.com/industrial/choosing-a-loctite-threadlocker-14075.htm

Tags: Henkel,LOCTITE,threadlocker,anaerobic threadlocker

How to Utilitize Loctite 262 Blue Threadlocker on Auto Repair

Anaerobic Threadlocker

The invention of the first anaerobic threadlocker made countless auto maintenance jobs easier. Find how more on our Vehicle Repair and Maintenance blog, there's a topic just for threadlockers: http://9nl.me/VRMChannel2/ More on threadlockers: http://9nl.me/VRMPage/

Tags: Automotive Industry (Industry),automotive maint...

Why you should use "Thread Locker / Loctite"

Anaerobic Threadlocker

If you fly RC models, you should use loctite or thread locker. Why you ask ? As it will keep you model from lossing screws midfligt, on a helicopter there are many more small vibrations then on a plane, so on a helicopter it is a NO GO, not to use it. When I put a new helicopter together, i wi...

Tags: hobbyking,rc,helicopters,loctite,thread,locker,...