XCSOURCE 5 pcs 1A 5V Micro USB TP4056 Lithium Battery Power Charger Board Module TE420

XCSOURCE 5 pcs 1A 5V Micro USB TP4056

MINI USB input terminal with a female, can be directly input to do with the phone charger rechargeable lithium battery, and still retains the input voltage wiring pads, can be very convenient DIY. This module is used for single-cell lithium or lithium multi-section parallel, charging ports can take power from USB. Specifications: Input Voltage: 4.5~5.5V Full charging voltage: 4.2V Max output current: 1A Power Indicator: Red stands for charging, Green stands for fullly charged. Input interface: MINI interface Item Size: 25mm*19mm. It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection. Instructions / Precautions: Test current meter in series with the charge sheet only 5V input. Charge current is best battery capacity 0.37C, is 0.37 times the capacity, such 1000mAH battery charging current 400 this is enough. The effect of excessive charging speed backward, rushed over battery voltage out on much! Not too small and too long charging connector wires. Such big connection resistance. Too thin, then rushed over battery voltage out on much. Connected to the battery the best good contact. Otherwise rushed over battery voltage out on much. If the 5V input voltage is high, such as 5.2 or even 5.5, will result in insufficient cha...

  • Brand: XCSOURCE
  • ASIN: B01DRT4PWY

CHENBO 10 Pcs 5V Micro USB 1A 18650 TP4056 Lithium Battery Charging Board With Protection Charger Module

CHENBO 10 Pcs 5V Micro USB 1A 18650

Input voltage: 5V Charging cut-off voltage: 4.2V ± 1% Maximum charge current: 1000mA Battery over-discharge protection voltage: 2.5V Battery overcurrent protection current: 3A Board size: 2.6 * 1.7CM Note: The first time you access the battery, it may no voltage between the output OUT + and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B + B-, then draw a line on the short open also need recharged to activate the protection circuit. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge + MICRO USB female and next - pads for the power input, access 5V. B + positive then the lithium battery, B- then negative lithium batteries. OUT + and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load. Package:10 pcs

  • Brand: CHENBO
  • ASIN: B06XCXPY86

Guest 2720A ChargePro On-Board Battery Charger 20A / 12V, 2 Bank, 120V Input

Guest 2720A ChargePro On-Board Battery Charger 20A /

For more than forty years, Marinco has been a global leader in harsh environment electrical products.  From shore-power connections, to power conversion and power management products to accessories, Marinco offers a broad range of high-quality, electrical components. All Marinco components feature rugged, corrosion-resistant construction, and meet rigorous global marine, RV and industrial standards. 

  • Brand: Guest
  • ASIN: B079SZFFL2
  • UPC: 046904904136

Makerfocus 10pcs TP4056 Charging Module 5V Micro USB 1A 18650 Lithium Battery Charging Board with Protection Charger Module

Makerfocus 10pcs TP4056 Charging Module 5V Micro USB

10pcs TP4056 Charging Module 5V Micro USB 1A 18650 Lithium Battery Charging Board with Protection Charger ModuleDescription:Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery.And still retains the input voltage wiring pads, can be very convenient DIY.Note: The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly.Note: The first time you access the battery, it may no voltage between the output OUT + and OUT-, then access 5V voltage charge your energy can activate the protection circuit, and the battery from the B+ B-, then draw a line on the short open also need recharged to activate the protection circuit. Note that the charger must be able to output 1A or more to do when using a mobile phone charger input, or may not charge.+ MICRO USB female and next - pads for the power input, access 5V. B + positive then the lithium battery, B- then negative lithium batteries. OUT + and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load.Connect the battery to the B + B-, inserted into the USB female mobile phone charger, the red light is being charged, the green l...

  • Color: 18650 Lithium Battery Charging Board
  • Brand: MakerFocus
  • ASIN: B071RG4YWM
  • UPC: 190033766643

Icstation TP4056 Micro USB 5V 1A 18650 Lithium Battery Charger Board, with Overcharge Over-Discharge Over-Current Protection (Pack of 10)

Icstation TP4056 Micro USB 5V 1A 18650 Lithium

IS-Icstation mini Li-ion battery charger board, built-in TP4056 chip, set charging and battery over-charge over-discharge over-current protection all in one practial for your DIY 18650 battery power supply to prolong its lifetime. On-board micro USB and soldering joints 5V input port and charging status indicator ideal for single-cell lithium or multi-section parallel lithium battery. Specifications:Chip: TP4056Input Voltage: DC5V Charging Cut-off Voltage: 4.2V±1% Maximum Charging Current: 1A Battery Over Discharge Protection Voltage: DC2.5V Battery Over Current Protection Current: 3A Board Size: 26 X 17mm/1.02 X 0.67inch(L*W) Package Included: 10 Pcs TP4056 Micro USB 5V 1A 18650 Lithium Battery Charger BoardNotice Please:1.when use this module at first time, there may be no voltage output between OUT+ and OUT-, it need connect the 5V power supply to active the circuit; When the battery disconnect with this module and connect it again also need this step. 2.When use the phone power adapter as the input power supply, it need the power adater output current is over 1A.3. If you have any question about products, application and delivery, please send us an email firstly, we will follow up in 12 hours during the business days, thank you!

  • Color: Blue
  • Brand: IS
  • ASIN: B01LHD9D7E

NOCO Genius GEN2 20 Amp 2-Bank On-Board Battery Charger

NOCO Genius GEN2 20 Amp 2-Bank On-Board Battery

The GEN2 On-Board Battery Charger offers the perfect mix of high-technology and rugged construction. With a fully-sealed, waterproof housing, the GEN2 can be easily installed and mounted directly onto a variety of applications and specifically designed for tough marine environments. Its waterproof design is capable of withstanding submersion down to 3-meters for extended periods of time without failure, and rated IP68 and NEMA 6P, providing continuous operation in the most extreme environments. The GEN Series On-Board Battery Chargers are some of the most advanced charging technology in its class. Utilizing the latest topology and power design, it is one of the most compact and lightweight battery chargers. Its onboard processor is capable of detecting, diagnosing, recovering, charging and maintaining all types of lead-acid batteries. Safely charge Wet Cell (Flooded), Gel Cell, AGM and Deep-Cycle batteries with zero overcharge. Plus, it protects against reverse polarity, sparks, short circuits, open circuits, and thermal runaway. And the GEN Series On-Board Battery Chargers are completely automatic. It continuously monitors the battery - while detecting any potential battery problems - shutting off power when the battery is fully charged, but observing the battery for optimal bat...

  • Color: Black|Blacks
  • Brand: NOCO
  • ASIN: B003JSJS5I
  • UPC: 046221090277

2Pcs 3S 11.1V 12.6V 25A W/Balance 18650 Li ion Lithium Battery PCB Protection Board

2Pcs 3S 11.1V 12.6V 25A W/Balance 18650 Li

Product Description Features: 100% Brand New and High Quality Strictly according to the diagram wiring: 0V(B )3.7V(B1)7.4V(B2)11.1V(B+), Do not deliberately short circuit. After the line is connected, Need to charge first, then have output. When the battery is connected in series with 3 groups, Please ensure that the voltage of each battery is the same. If not same, please fill in each set of batteries and then use. Do not mix the good battery and the battery. The capacity of the battery internal resistance is closer will be better. Attention: Do not mix the good battery and poor battery to use. The internal resistance of 3 battery capacity are closer will be better. Please buyers know the professional knowledge of this module before buying. Specification: Over voltage range: 4.25 4.35v¡À0.05v Over discharge voltage range: 2.3 3.0v¡À0.05v Maximum operating current: 0 25A Maximum transient current: 34 40A Quiescent current: less than 30uA Internal resistance: less than 100m? Working temperature: 40 +50? Storage condition: 40 +80? Effective life: more than30000h Short circuit protection: Yes, delayed self recovery Size: 56mm*45mm*1.2mm(LXWXH) Material: PCB Color: Green Quantity: 1 PC Net Weight: 12g Note: Lighting, display and other factors may cause COLOR SHADING, please comp...

  • Brand: daier
  • ASIN: B07JMY631D

Anmbest TP4056 Micro USB Open Source 5V 1A 18650 Standalone Linear Lithium Battery Charger Over Charge Discharge Protection Integrated Board(Pack of 10)

Anmbest TP4056 Micro USB Open Source 5V 1A

This module is made for charging rechargeable lithium batteries using the constant-current/constant-voltage (CC/CV) charging method. In addition to safely charging a lithium battery the module also provides battery overcharge overdischarge protection. This module greatly simplifies the process of adding single cell Lithium battery power to your projects. Just connect the battery terminals to the indicated pads on the board and connect your output leads. The module keeps both cell voltage and current draw within safe tolerances, so there's little worry of damaging your battery. Technical Specifications: Input Voltage: DC5V Charging Cut-off Voltage: 4.2V±1% Maximum Charging Current: 1A Battery Over Discharge Protection Voltage: DC2.5V Battery Over Current Protection Current: 3A Constant-Current/Constant-Voltage Board Size: 26 X 17mm/1.02 "X 0.67"(L*W) Package includes: 10 x TP4056 Lithium Battery Charger and Protection Module PRECAUTIONARY NOTE 1.when use this module at first time, there may be no voltage output between OUT+ and OUT-, it need connect the 5V power supply to active the circuit, When the battery disconnected from B+ B- and then connected again with this module also need this step. 2. Most modern phone/USB chargers can provide 1A or more; refer to th...

  • Brand: Anmbest
  • ASIN: B07CQN6GVJ

Diymore 10pcs Micro USB 5V 1A 18650 TP4056 Lithium Battery Charging Board Charger Module with Dual Protection Function

Diymore 10pcs Micro USB 5V 1A 18650 TP4056

Product Description: Inputs with MICRO USB female, can be directly input to do with the phone charger rechargeable lithium battery. And it still retains the input voltage wiring pads, can be very convenient DIY. + MICRO USB female and next - pads for the power input, access 5V. B + positive then the lithium battery, B- then negative lithium batteries. OUT + and OUT- connected to the load, such as positive and negative electrodes connected mobile booster plate or other load. Connect the battery to the B + B-, inserted into the USB female mobile phone charger, the red light is being charged, the green light to full. Specification: The input voltage: 5V Input interface: micro USB Charge cut-off voltage: 4.2V + / - 1% Maximum charging current: 1000mA Battery over-current protection current: 3A The battery overcharge protection voltage: 2.5V Note: The charge should disconnect the load OUT terminal on the positive and negative can not be wrong, please according to specifications, otherwise it will damage directly. The first time you access the battery, it may no voltage between the output OUT + and OUT-, then access 5V voltage charge your energy can activate the protection circuit. And the battery from the B+ B-, then draw a line on the short open also need recharged to activate the...

  • Color: Fast Charging Station - model FC130
  • Brand: diymore
  • ASIN: B01J7FXZLY
  • UPC: 611029136009

XCSOURCE 10pcs 1A 5V Micro USB TP4056 Lithium Battery Power Charger Board Module TE585

XCSOURCE 10pcs 1A 5V Micro USB TP4056 Lithium

Features: With a Micro USB port, can be charging rechargeable lithium battery directly as a phone charger. Retains voltage input wiring pads, convenient for DIY. This module can charge for single-cell lithium battery or multi-section parallelled lithium batteries, can be powered by USB ports. With LED indicators, easily read the charging status. Specifications: Input Voltage: 5V Full charging voltage: 4.2V Max output current: 1A Power Indicator: Red for charging, Green for fully charged. Input interface: Micro USB Charging Precision: 1.5% Operating Temperature: -10 ° C ~ +85 ° C Item Size: Approx. 25 x 19mm. It can be used for voltage 3.6, 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection. Current Regulation: RPROG(k) - IBAT(mA) 30k - 50mA 20k - 70mA 10k - 130mA 5k - 250mA 4k - 300mA 3k - 400mA 2k - 580mA 1.66k - 690mA 1.5k - 780mA 1.33k - 900mA 1.2k - 1000mA Cautions: 1. Please make sure the battery is well connected. 2. Please do not connect the output reversely, otherwise it may burn the chip. 3. The connection wire should not be too thin or too long. 4. Current meter can only be connected with the module in series with 5V input. 5. Charging current is better to be 37% of the battery capacity. If you want to charge a battery of 1000mAh, 400m...

  • Brand: XCSOURCE
  • ASIN: B01LZSC7I8

DACHENGJIN Cable Kaisi K-9206 Professional Battery Activation Charge Board with Micro USB Cable for Samsung/Oppo/Xiaomi/Vivo/Huawei

DACHENGJIN Cable Kaisi K-9206 Professional Battery Activation Charge

1. For activating the dormant battery, makes the dormant battery working normally again2. Current adjustable from 1-2A, safe and fast charging3. Overcurrent protection starts when the electric current is over 2A4. Short circuit testing to judge the working condition of battery5. It needs the working voltage over 2.5V to work normally6. Maximum charging electric current is 2A

  • Brand: DACHENGJIN
  • ASIN: B07SFXRMM2

MinnKota MK 315D On-Board Battery Charger (3 Banks, 5 Amps per Bank)

MinnKota MK 315D On-Board Battery Charger (3 Banks,

  • Color: Black
  • Brand: Johnson Outdoors
  • ASIN: B0042T8XRC
  • UPC: 803982953865

Anmbest 5PCS 3S 11.1V/12V/12.6V 10A 18650 Charger PCB BMS Protection Board for Li-ion Lithium Battery Cell

Anmbest 5PCS 3S 11.1V/12V/12.6V 10A 18650 Charger PCB

Specifications: Charging voltage:12.6v ~ 13v Over Charge voltage:4.25 ~ 4.35v Over Discharge voltage: 2.3 ~ 3.0v Max Working current:6 ~ 8A Max peak current:10 ~ 13A Internal resistance: Less than 100mΩ Working temperature:-40 ~ +50 Storage Temperature:-40 ~ +80 Quiescent current:

  • Color: Red-4931
  • Brand: Anmbest
  • ASIN: B07DYS6RJJ

NOYITO 30A 4S 3.7V Lithium Battery Protection Board 14.8V with Balance Over-Current Over-Charge Over-Discharge Protection

NOYITO 30A 4S 3.7V Lithium Battery Protection Board

USAGE NOTES: 1: Please wire strictly according to the wiring diagram,can not short circuit! 2: After the wire is connected, it needs to be charged first then output. 3: When connecting 4 batteries in series, please make sure that the voltage of each battery is the same. If not, please full each battery separately and use it in series. In the discharge test, the battery with the fastest voltage drop was the bad battery. Explain: Do not mix good and bad batteries together! The capacity/internal resistance of the 4 batteries is as close as possible (2 good batteries + 2 bad battery = 4 bad batteries). The lithium battery protection board parameters: Maximum operating current: 30A Maximum instantaneous current: 56A Over charge voltage range: 4.25-4.35V±0.05V Quiescent current: less than 30uA Internal resistance: less than 20mΩ Charging voltage: 16.8V-18V Charging current: 20A Max Working temperature: -40 - +50°C Storage conditions: -40 - +80°C Short-circuit protection: Trigger condition: External load shorted. Release condition: disconnect the load. Size: 56*48*4.0mm Package Included: 1pcs 30A 4S 3.7V Lithium Battery Protection Board

  • Color: Green
  • Brand: NOYITO
  • ASIN: B07BVRKG37
  • UPC: 667797748630

KNACRO 30A Battery Charge Controller Protection Switch DC 6V-60V Battery Protection Board for Lead Acid Battery and Lithium Battery

KNACRO 30A Battery Charge Controller Protection Switch DC

This digital battery charging protection switch is specially designed for the DC6-60V battery. On-board momentary push button to set the charging initiation voltage and charging stop voltage, when the battery voltage reaches the setting value, the module will disconnect the charging circuit automatically to aviod the battery from overching to prolong the battery lifetime. Specifications: Input Voltage Range: DC6-60V Dispaly and Control Accuracy: 0.1V Compatible Battery: lead acid, lithium ion battery, solar panel battery (DC 6-60V) Board Size: 81 X 54 X 18mm / 3.19 X 2.13 X 0.71inch (L * W * H) Operation Manual: 1, connect the battery; 2, Press + to display the upper voltage, long press the flash to set the upper voltage. 3, press - to display lower limit voltage, long press flash to set lower limit voltage 4, connect the appropriate voltage charger, you can charge the battery 5, Normally press Set to close the screen. Note: This module do not have the buck converter function. Package Included: 1X Lead Acid Lipo Battery Charge Controller If you have any question , please feel free to contact us. KNACRO highly appriciate all customers' opinions to improve the selling ,also if anything you unsatisfied, pls contact our customer service department for probable best solution. Fee...

  • Brand: KNACRO
  • ASIN: B07BGTKM5F
  • UPC: 736364874161

McIgIcM 5pcs Micro USB 5V 1A 18650 TP4056 Lithium Battery Charger Module Charging Board with Protection Dual Functions 1A Li-ion

McIgIcM 5pcs Micro USB 5V 1A 18650 TP4056

1. MINI USB input terminal with a female, can be directly input to do with the phone charger rechargeable lithium battery, And still retains the input voltage wiring pads, can be very convenient DIY. 2. It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection. 3. Input voltage: 5V 4. Charging cut-off voltage: 4.2V 5. Maximum charge current: 1000mA 6. Battery over-discharge protection voltage: 2.5V 7. Battery overcurrent protection current: 3A 8. Board size : 17.16 mm x 26.17 mm

  • Brand: MCIGICM
  • ASIN: B06XQRQR3Q
  • UPC: 724190025208

WMYCONGCONG 10 PCS 5V 1A Boost Step Up Power Supply Module Lithium Battery Charge Protection Board 134N3P DIY Charger LED Display USB and Micro Port

WMYCONGCONG 10 PCS 5V 1A Boost Step Up

Specification: Board Size: 22 * 17 * 10mm/0.87 * 0.67 * 0.39inch(L * W * H) Input Voltage: 3.7V-5.5V Charging Current: Z 1A Output Current: Z is 1A Output Voltage: 5V BAT Discharge Termination Voltage: 2.9V Preset 4.2V Charge Voltage with ±1% accuracy Discharge Efficiency: 85% (input 3.7V, output 5V/1A) Package Content: 10 * 5V 1A Boost Step Up Power Supply Module

  • Brand: WGCD
  • ASIN: B07KJVGVCM
  • UPC: 705169050407

NOYITO 12V 24V Battery Charging Control Board (12-24V MAX30V) Battery Charge Control Switch Auto Power Off Safe and Energy Saving

NOYITO 12V 24V Battery Charging Control Board (12-24V

Product Name: Battery Charge Control Module; Input voltage: DC12-24V (MAX 30V);The maximum current can be controlled by 20A. (If the board is working for a long time, it is recommended not to exceed 15A) Display accuracy: 0.1V; Control accuracy: 0.1V; Voltage error: ± 0.1V; Output type: direct output; Scope: 12-24V of various types of batteries. Net weight: 40g. Product size: 81 * 54 * 18mm / 3.19 * 2.13 * 0.71in (L * W * H). Suitable for use in household chargers, solar energy, wind turbines. Instructions: In the set voltage value state, the start button to play the role of up, stop the button to play down the role. Set the starting voltage: Support display voltage state, press the start voltage button once to show the start charging voltage. Long press the start button for 3 seconds, digital flashing, through the start and stop button to set the start charge voltage value. To set the stop voltage: In the normal display voltage state, press the stop voltage button once to display the stop charging voltage. Long press the stop button for 3 seconds. Press the stop button for 3 seconds, digital flashing, through the start and stop button to set the stop charge voltage value. Reset: Power state at the same time press and hold the start and stop button, display 888, that is, resto...

  • Brand: NOYITO
  • ASIN: B01MRV4BBE
  • UPC: 603983633663

AKK XT60 Parallel Charging Board/Charge Plate Banana Plug Input for 3S 4S Lipo Battery

AKK XT60 Parallel Charging Board/Charge Plate Banana Plug

Specifications: Compatible battery types: 3S/4S Lipo Input connector: banana plug Output connector: XT60 Maximum charging current: 20A Fuse: 30A fuse×3 (replaceable) No-load current: 17mA-22mA Board size: 8*5cm Weight: 65g/0.14 lb Cable length: banana plug cable: 17cm                        5 pin cable: 15cm Package Includes:  1x XT60 charging board for 3S/4S Lipo battery Voltage display: It will display a total voltage firstly;then display average voltage of single cell in a 3 seconds cycle ("OC1"=the 1st cell; "OC2"= the 2nd cell...)    Note: 1. Only supports charging the same type of battery at the same time(3S/4S Lipo) 2. Please keep it in a safe place to prevent short circuits

  • Brand: AKK
  • ASIN: B07FR7X21Q

Kaisiking Professional Battery Tester Battery Activation Charge Board, Phone Battery Repair Circuit Board with Power Current Cable Compatible for iPhone X 8 7 Plus 6 Plus 6S, iPad, Samsung, Oppo etc.

Kaisiking Professional Battery Tester Battery Activation Charge Board,

Kaisiking prifessional cell phone battery repair activation charge circuit board for iPhone Android phone 1.This Battery tester doesn't contain battery, it is only used for testing, charging, and re-activate iPhone iPad Android batteries. 2.This is the professional testing and re-active battery tester, not for one-time used, we suggest that DIY enthusiasts can resell it out. Description: The battery test charge / activation board brings old or dead iPhone batteries back to life, it is a valuable phone repair tool for battery. Advanced design allows you to charge a maximum of two batteries at any one time. 2A Current Protection/cut off, if the current of voltage are too high the protection automatically disconnects the power supply. Short circuit protection: If the battery has a short-circuit, the warning lamp will illuminate - Do not to charge the battery! Visual display - A dual LCD display showing current & voltage. Safe and easy to use - Attach battery and power to use, when the battery is full it will stop the output charge current to prevent overcharging. Low voltage activation: os battery voltage is below 3V, the battery can be re-activated using the activation button. More Info & Note: Keep the input voltage below 5V. It's better to charge one battery at a time for a faste...

  • Color: 9208 Tester Board
  • Brand: Kaisiking
  • ASIN: B077M6R86P
  • UPC: 760960439967
Similar Battery Charge Board Results
Battery Charge Board Video Results
           

TP4056 Li-ion Battery Charging with Protection Board - Micro USB 5V interface

Battery Charge Board

This video shows In this video simple how to make a 3.7v TP4056 Li-Ion Lithium Battery charger with Protection Board Charging Module - Micro USB Interface Seeedstudio PCB order website - https://www.seeedstudio.com/fusion_pcb.html -----------------------------------------------------------------...

Tags: tp4056,battery charger,lipo,18650,charger,diy,b...

Simple DIY 18650 Battery Charger - TP4056 Review (Everything Explained)

Battery Charge Board

18650 lithium-ion cells. These type of batteries are very popular nowadays. And a good charger is very expensive. This is the most detailed tutorial on how to make your own cheap but very good - 18650 battery charger. For each cell you need a charging module and a battery support. For a chargi...

Tags: diy,18650,cell,cells,charger,battery,best,tp405...

Universal Battery Charger Make using TP4056 Charger Module

Battery Charge Board

In this video I'm showing a DIY method to make a universal phone Battery or any Lithium Battery (18650 Battery) charger by using TP4056 Micro USB 5V 1A Lithium Battery Charging Module Board TE585 Lipo Charger. You can get the Charger Module (DIY 18650 Battery Charger - With TP4056 Module) : http...

Tags: TP4056,5V 1A USB 18650 Lithium Battery,Lithium ...