DuPont Teflon Non-Stick Dry-Film Lubricant, 14-Ounce

DuPont Teflon Non-Stick Dry-Film Lubricant,

DuPont Non-Stick with Teflon Fluoropolymer is a unique dry-film lubricant made of 100% Teflon and surface binding agents. Dry lubricant will repel abrasive contaminants while lubricating. Formulated with Teflon for longer lubricant life, enhanced wear protection, better high and low temperature range and increased resistance to water. Use on surfaces requiring a dry, non-oily, non-staining, silicone-free film. Effective from -100°F to 480°F (-73°C to 250°C). Use on cutting surfaces such as saw blades, drill bits or on flat surfaces such as table saws. Works to lubricate tight tolerance gears or flat sliding surfaces such as treadmills.

  • Brand: DuPont
  • ASIN: B00D3G6IFE
  • UPC: 036121193017

Photosensitive (30cmx500cm/1ftx16.5ft) PCB Photosensitive Dry Film for Circuit Production Photoresist Sheets, Replace Thermal Transfer PCB Board

Photosensitive (30cmx500cm/1ftx16.5ft) PCB Photosensitive Dry Film for Circuit

Commitment:You can get the full refund,If the product you received not include the VANTIYAUS Box!!!Just contact Amazon team without any other reason.Etching: The dry film is resistant to most of the acid etching solution, the PH value can be resistant to most alkaline etching solution between PH8.0 ~8.5. Cover hole: 1.5 mil dry film can fully cover a 0.25 inches thickness hole. Plating: The dry film is available in most common use of the plating bath, no wrinkles, no color. Package include: 1x photosensitive dry film1x VANTIYA  Paper protector BoxOperating Steps:1-Grinding CCL, this simple, using the finest polished clean water frosted paper on the line2-Removing film, photographic film is sandwiched between two layers of film, the first side can make use of transparent tape tear torn, try a few on the line3-And then foil, copper clad laminates can look a little cleaner, pasted, try not to have bubbles4-Good paste membrane used presses, not too hot, about 100 degrees from the fixing5The printed circuit board film, suggestion is to use film, the fine could reach the highest degree of accuracy if you did not ask for the paper to print it with sulfuric acid trip6The printed circuit on the photographic plate (Note: Dry film is negative, so to highlight the print, which we u...

  • Brand: VANTIYAUS
  • ASIN: B01NCS88LU
  • UPC: 729910302997

WD-40 300052 Specialist Dirt and Dust Resistant Dry Lube PTFE Spray 10 OZ (Pack of 1)

WD-40 300052 Specialist Dirt and Dust Resistant Dry

WD-40 Specialist Dirt and Dust Resistant Dry Lube PTFE Spray - High Temperature Lubricant up to 500° F. 10 oz. (Pack of 1)

  • Color: Multicolored
  • Brand: WD-40
  • ASIN: B00AF0ODGM
  • UPC: 079567300052

DuPont Teflon Silicone Lubricant Aerosol Spray, 14 oz

DuPont Teflon Silicone Lubricant Aerosol Spray, 14

DuPont Silicone Lubricant with Teflon Fluoropolymer waterproofs, protects, lubricates and preserves rubber, plastic, vinyl, leather, metal and wood. This silicone-rich formula is a great all-purpose lubricant around the home, shop and worksite. Use on treadmills, sliding parts, windows, doors, rubber door gaskets, and much more. Formulated with Teflon fluoropolymer to outperform other Silicone Sprays in terms of longer lubricant life, enhanced wear protection, better high and low temperature range and increased resistance to water. Performs in extreme temps from -40-Degree F (-40-Degree C) to 400-Degree F (204-Degree C).

  • Brand: DuPont
  • ASIN: B00D3ZKVAS
  • UPC: 036121176133

Prime-Line Products RZ 50 9.0-Ounce Dry Film Lubricant

Prime-Line Products RZ 50 9.0-Ounce Dry Film

Dry Film Spray Lubricant, Will not attract dust, inhibits rust, safe on any surface. Use on closet rollers, drawer, garage doors, locks, anything that moves.

  • Brand: PRIME-LINE
  • ASIN: B00E8AFBDO
  • UPC: 681488501120

1 Roll Photosensitive Dry Film PCB Photoresist Film for Circuit Production Photoresist Sheets 30cmx1m

1 Roll Photosensitive Dry Film PCB Photoresist Film

Specification: Brand new Type: photosensitive dry film Color: as picture shows Size: approx. 30*100cm / 11.81'' x 39.37'' Quantity: 1 roll PCB photosensitive dry film for circuit production Features: Photographic film, also known as dry film, is used to make PCB board, stick it on top of the PCB, it will become a sensitive circuit board. Suitable for plating, hole covering, and the etching process. Excellent ability to cover holes High Resolution Excellent adhesion to almost all surfaces Image clarity after exposure Front-panel is very clean after developed How to use it: Clean your board. Cut dry film a little larger than your board. Apply Resist: This Photoresist has 3 layers, the top and bottom layers are clear protective layer, so at the first, you need remove one protective layer, the easy way is to use two small pieces of scotch tape. Then apply the middle layer on board. Expose: Place your negative artwork over the rest protective layer. Develop: Remember: you need NEGATIVE film developer, Remove the rest protective layer on the film. After 3 minutes take board out of developer and hold under running water to check, you can always place it back in the developer if needs more time.

  • Brand: Jwn
  • ASIN: B07BT5KQ2C

DeFelsko PosiTector 6000 F1 Coating Thickness Gauge Standard Model with Built-in Probe for Ferrous Metal Substrates (0-60 mils/1500 um) - Complete kit.

DeFelsko PosiTector 6000 F1 Coating Thickness Gauge Standard

' Coating Thickness Gage, Electronic, Base Material Ferrous Metals, Measuring Range 0 to 60 Mils, Accuracy +/-(0.05 Mils + 1 Percent) up to 2 Mils Then +/-(0.1 Mils + 1 Percent), 3 ft Cord Length, NIST Calibration Certificate, AAA Battery Type, Includes Precision Plastic Shims, Rubber Holster with Belt Clip, (3) Batteries, Wrist Strap, Nylon Carrying Case with Shoulder Strap, and Instructions, Manufacturers Warranty Length 2 Years '

  • Brand: DeFelsko
  • ASIN: B0052P4B7G

Sprayon MR311 DRY FILM RELEASE AGENT 12 oz Aerosol, SKU #S00311000

Sprayon MR311 DRY FILM RELEASE AGENT 12 oz

Sprayon® MRTM 311 Dry Film Release Agent, 12 oz Aerosol, contains fluoropolymer, which provides an extremely thin, dry film that does not transfer to finished parts. Allows multiple releases per application and is compatible with most moldable resins and elastomeric compounds, as well as delicate urethanes. Will not interfere with post-finishing operations.

  • Brand: Sprayon
  • ASIN: B00DRHTFH2

Photosensitive Film(30cmx500cm/1ftx16.5ft) PCB Dry Film,for Photosensitive PCB Circuit Production Photoresist Sheets,Replace Thermal Transfer PCB Board

Photosensitive Film(30cmx500cm/1ftx16.5ft) PCB Dry Film,for Photosensitive PCB Circuit

Commitment:Youcan get the full refund,If the product you received not include the VANTIYAUSBox!!!Just contact Amazon team without any other reason.Product description:Features:1.5 milthickness of dry film can be completely cover a hole of 0.25 inchesThe dryfilm can be used in the most ordinary plating solution, no wrinkle, nodiscoloration Product information:Specification:Condition:100% Brand NewWeight:Approx. 55g / 1.9ozSize:Approx. 1 * 0.3m / 3.3 * 1.0ft Package List:1 *Photosensitive Dry FilmNote:Order from VANITYAUS it's 100% original ,but ordered from others could be fake oneand without security. 

  • Brand: VANTIYAUS
  • ASIN: B07PMJJK2D
  • UPC: 631105302289

Loctite 1786074 LB 8017 Moly Dry Film Lubricant, 12 oz. Aerosol Can

Loctite 1786074 LB 8017 Moly Dry Film Lubricant,

LOCTITE LB 8017 is a molybdenum-disulfide based solid film lubricant. It is a heavy-duty lubricant used for general plant maintenance, metal working trade, machinery manufacturers and manufacturers of military and commercial jet engines. For continuous use in sliding friction, at temperatures from -29 °C to +400 °C. For anti-seize lubrication, LOCTITE LB 8017 functions from -29 °C to +1315 °C . Typical applications include Maintenance - threaded lubricant, dry bearing surfaces, slides, guides, pins, conveyor chains, exposed "dry" gears, flexible shafts, press fits, valve stems, shaft/packaging wear-in, "easy off" coating for boiler exhaust surface deposits, power transmission couplings, Production - swaging, metal forming, cold extrusion, warm extrusion, cold and warm headings, "dry" lubricant for mechanical linkages, Aerospace - gas turbine engine blades, valves, bearings, vacuum and radiation applications, Automotive, Heavy Equipment - cam wear-in, brake mechanisms, cables, gear couplings, Electrical - circuit breakers, rheostats, switches, Petro Chemical - valves, boilers, flanges, dampers.

  • Brand: Loctite
  • ASIN: B01HVP7FUY
  • UPC: 079340003668

Finish Line Pedal and Cleat Dry Film Lubricant Aerosol, 5-Ounce

Finish Line Pedal and Cleat Dry Film Lubricant

Clipless pedals require regular maintenance for optimum performance and long component life. Finish Line Pedal & Cleat Lubricant sprays on to fully and evenly coat all frictional surfaces and is engineered to ensure fast engagements and smooth releases every time. Thanks to a 100% dry-to-the-touch micro-thin coating, there is no oily, greasy film or unwanted stain when you walk around in your shoes. Pedal & Cleat Lubricant is formulated specifically with DuPont Teflon fluoropolymer and surface bonding resins to create an ultra slick, protective dry film. This film does not absorb abrasive contaminants, which reduces friction, prevents annoying squeaks and premature wear. It also helps prevent corrosion by repelling moisture. Pedal & Cleat Lubricant was designed and formulated to maximize the performance of any pedal and cleat system and is so effective that it is factory approved by Speedplay.

  • Color: Original Version
  • Brand: Finish Line
  • ASIN: B00N4OO6EA
  • UPC: 036121710283

ANTI-SEIZE TECHNOLOGY 12014 Moly-Spray Dry Film Aerosol Lubricant, Black, (Net weight: 14 oz.) 20 oz.

ANTI-SEIZE TECHNOLOGY 12014 Moly-Spray Dry Film Aerosol Lubricant,

Moly-Spray Dry Film Lubricant is an air-drying, solid film lubricant convenient to apply and ready to use in minutes. It forms a thin dry film of molybdenum disulfide, which has a low coefficient of friction and effective corrosion resistance. It is non-oily, non-sticky, and will not cold flow, run, or drip. Moly-Spray Dry Film Lubricant performs under extremely heavy loads (10,000 psi),as a dry film lubricant for temperatures -300° to +750°F (-184° to +400°C), and up to 2400°F as an anti-seizing agent.

  • Color: Black
  • Brand: Anti-Seize Technology
  • ASIN: B00K6ZSOS4
  • UPC: 815443016934

6 Inch 800 Grit High Performance Hook and Loop Wet / Dry Film Sanding Discs, 10 Pack

6 Inch 800 Grit High Performance Hook and

6 Inch 800 Grit Hook and Loop Wet / Dry Autobody Film Sanding Discs, 10-Pack. Premium waterproof polyester film with industrial grade aluminum oxide (A/O) grain. Self fracturing Aluminum Oxide provides a fast cut rate with excellent longevity. Superior strength and durability compared to paper backed sanding discs. Ideal for use on auto body, fiberglass, plastics, composites, marine finishing and high gloss finishing. Flexible polyester film offers superior performance on curve, corner, and edge sanding applications. Discs are precision stamped and bonded with hook and loop backing. Resin over resin bonding resists heat and humidity. Wet or dry applications. IMPORTANT: The extra thick zinc stearate coating on these discs offers superior lubrication and requires less water than typically used in wet applications. Water misting is more effective than a steady stream. Material released from the disc surface during use is NOT abrasive grain, it is zinc stearate. This coating is designed to slough off gradually while providing close tolerance and a perfectly even surface finish.

  • Brand: Red Label Abrasives
  • ASIN: B00CMTKEQW

DuPont Teflon Multi-Use Lubricant, 14-Ounce

DuPont Teflon Multi-Use Lubricant,

DuPont Multi-Use with Teflon Fluoropolymer is a high-performance general purpose lubricant with extreme corrosion and wear protection. Water repelling, silicone-free formula protects against heavy moisture and rust. Formulated with Teflon for longer lubricant life, enhanced wear protection, better high and low temperature range and increased resistance to water. Resists extreme temperatures from -30°F to +300°F.

  • Brand: DuPont
  • ASIN: B008S7OHF6
  • UPC: 036121191587

Graphite Dry Film Lubrcnt, Aerosol, 12 oz.

Graphite Dry Film Lubrcnt, Aerosol, 12

'Graphite Dry Film Lubricant, Size 12 oz., Container Type Aerosol Can, Color Light Gray, Temp. Range -75 Degrees to 400 Degrees F, Flash Point None, Dielectric Strength Not Specified, VOC Content Not Specified, Application Reducing Friction in Sliding, Twisting or Spinning Parts, Bonds Quickly to Clean Metal, Wood'

  • Brand: SLIP PLATE
  • ASIN: B00869WCH6

Graphite Dry Film Lubricant, 1 Gal

Graphite Dry Film Lubricant, 1

' Heavy Duty Graphite Dry Film Lubricant, Size 1 gal., Container Type Can, Color Dark Gray, Temp. Range -75 Degrees to 400 Degrees F, Flash Point 105 Degrees F, Dielectric Strength Not Specified, VOC Content Not Specified, Metal Detectable No, Application Reduce Friction in Sliding, Twisting or Spinning Parts, Bonds Quickly to Clean Metal, Wood, Concrete, , Some Hard Plastic Surfaces '

  • Brand: SLIP PLATE
  • ASIN: B01LRIXOSS

Polaroid 2x3ʺ Premium ZINK Zero Photo Paper 50-Pack - Compatible with Polaroid Snap / SnapTouch Instant Print Digital Cameras & Polaroid ZIP Mobile Photo Printer

Polaroid 2x3ʺ Premium ZINK Zero Photo Paper 50-Pack

Photos so simple—it must be magic! Photography has always been a pricy hobby with all those films, ribbons, cartridges and equipment. It’s enough to make your wallet weep! Finally, the folks at Polaroid joined forces with ZINK to bring you easy, affordable photo-printing innovation. This bulk pack of Zero Ink Photo Paper is the perfect companion for all your favorite ZINK-compatible products including SNAP, SNAP Touch, Socialmatic and ZIP. Each sheet of 2”x3” sticky-backed paper promises crisp, crystal-clear imaging, brilliant color and rich detail only produced in a darkroom. Just press the shutter, and a gorgeous photo promptly arrives for instant viewing and sharing. It’s perfect for scrapbookers and selfie lovers everywhere. So say ‘no more’ to those maddening inks and toners—and add a pack to your cart today! Impeccable Color Detail Old photos seem ‘nostalgic,’ but in reality, that’s cloudy color and poor contrast. ZINK paper boasts sharp detail, superior color integrity and even tone, so pics are always insta-worthy. Long-Lasting Performance Our paper is engineered to withstand the test of time thanks to its glossy quick-dry polymer coating. It not only infuses a professional shine, but also protects against smudging, ripping and fading. Save More Than...

  • Color: Regular Color Border
  • Brand: Polaroid
  • ASIN: B008GVVUFE
  • UPC: 646437157339

DuPont Teflon Multi-Use Lubricant Aerosol Spray, 11 Oz.

DuPont Teflon Multi-Use Lubricant Aerosol Spray, 11

DuPont Multi-Use with Teflon Fluoropolymer is a high-performance general purpose lubricant with extreme corrosion and wear protection. Water repelling, silicone-free formula protects against heavy moisture and rust. Formulated with Teflon for longer lubricant life, enhanced wear protection, better high and low temperature range and increased resistance to water. Resists extreme temperatures from -30°F to +300°F.

  • Brand: DuPont
  • ASIN: B000GL19TY
  • UPC: 036121191570

6 Inch 400 Grit High Performance Hook and Loop Wet/Dry Auto Body Film Sanding Discs, 50 Pack

6 Inch 400 Grit High Performance Hook and

6 Inch 400 Grit Hook and Loop Wet / Dry Autobody Film Sanding Discs, 50-Pack. Premium waterproof polyester film with industrial grade aluminum oxide (A/O) grain. Self fracturing Aluminum Oxide provides a fast cut rate with excellent longevity. Superior strength and durability compared to paper backed sanding discs. Ideal for use on auto body, fiberglass, plastics, composites, marine finishing and high gloss finishing. Flexible polyester film offers superior performance on curve, corner, and edge sanding applications. Discs are precision stamped and bonded with hook and loop backing. Resin over resin bonding resists heat and humidity. Wet or dry applications. IMPORTANT: The extra thick zinc stearate coating on these discs offers superior lubrication and requires less water than typically used in wet applications. Water misting is more effective than a steady stream. Material released from the disc surface during use is NOT abrasive grain, it is zinc stearate. This coating is designed to slough off gradually while providing close tolerance and a perfectly even surface finish.

  • Brand: Red Label Abrasives
  • ASIN: B00BN04EXK

LPS Dry Film Silicone Lubricant, 11 oz Aerosol (Pack of 12)

LPS Dry Film Silicone Lubricant, 11 oz Aerosol

The dry film, silicone lubricant for rubber, plastic, and metal parts.

  • Color: Clear/Colorless
  • Brand: LPS
  • ASIN: B00LISTU9K
Similar Dry Film Results
Dry Film Video Results
           

How to make PCB using Photoresist Dry Film

Dry Film

Make your own printed circuit boards with Negative Photosensitive Dry Film. You can make fine pitch professional quality PCBs at home.Say goodbye to all of the old methods like marker pen,toner transfer etc. Items we need: 1.Copper clad board 2.Scrubber 3.Photoresist dry film (Negative resist) 4....

Tags: Make PCB,Photoresist,Printed Circuit Board,Phot...

PCB process using photoresist dry film

Dry Film

Printed Circuit Board process using photoresist dry film. Proceso de creación de un circuito impreso usando película fotosensible. If you want to see the same circuit test with the method of the toner transfer paper: Si quieres ver el mismo circuito de test con el método del papel de transferenc...

Tags: pcb,photoresist dry film,pelicula fotosensible,...

How to make PCB at home using photoresist Dry Film.

Dry Film

Don't you want to wait for the pcb delivery for weeks? With these instructions, you make the pcb yourself in an hour.

Tags: pcb,electronics,photoresist,dry film,etching,diy